Please look on eBay - that's where it will be listed!
Thanks
Click here to see the range of Wolfitt Racing products
SOLD Steering box and column for 1964 Ford Falcon, standard
ratio. Good working order.
SOLD Set 4 x 7J15 Compomotive MO 5-spoke alloy wheels, to fit 5
stud Ford Mustang, Falcon etc. £250
SOLD Hurst Indy - shifter handle 23cm length with black gear
knob - part number 0077, new and unused
SOLD Ford Axle half shafts - original type in excellent condition with 28 Splines to suit
Ford 8" or 9" axle. 5 Stud output flanges, lengths are 27" and 31"
SOLD Bench seats, front and rear for 1964 / 65 Ford Falcon,
red vinyl and in very good condition
SOLD Set of steel panels for 1964 Ford
Falcon - Front Wings, Boot, Bonnet, Doors - excellent condition, no trim or
winders etc.
SOLD Ford 3-speed manual
toploader gearbox
SOLD Set 4 x 8J15 Compomotive MO wheels, black with Avon slicks
(whole lot just one race old) to fit Triumph TR7 / TR8 / TR7V8 - same PCD as
Spitfire, Herald, Marina and MGF, excellent condition.
SOLD Truly awesome Stainless
Steel tubular 6-3-1 exhaust manifold with equal length primaries - complete with
full stainless system for Vixen 2500 or M Series 2500, this is all brand new and
unused - manifold is heat treatment coated. May fit GT6 or TR5 / TR5
SOLD Triumph Spitfire 1500
or GT6 Mk III, pair, excellent 'long' swing axles complete with Spitfire/Herald
brake drums etc (will fit any Spitfire or Herald)
SOLD Holley 600 1850-4 vacuum secondary
SOLD Remote oil cooler fitting kit , has spin on oil filter
conversion, remote oil stat, 4 x 5/8 BSP oil hoses for GT6, TR6 or Triumph
2000/2500
SOLD Vixen / Grantura radiator, all aluminium, brand new
SOLD Vixen radiator, copper and brass type in good condition
SOLD Triumph 2500 6 Cylinder engine; fully professionally rebuilt and
unused since rebuild. With new fast road BP285 Piper camshaft, ported, unleaded
cylinder head, new pistons, rings, oil pump, camshaft chain, vernier cam chain
wheel, chrome rocker box, all new bearings etc etc. Fabulous condition.
SOLD Heated glass rear screen (tinted) for TVR Tuscan and Vixen (same
as M series I think). Very rare!
SOLD Triumph TR6 gearbox with J Type overdrive, fully reconditioned
and as new
SOLD Triumph TR5 or TR6 differential / final drive unit, 3.45 ratio;
fully, professionally rebuilt
SOLD Brake pads, Ferodo DS3000 FER FRP219 R for AP calipers CP3345
brand new in box (bought for the TR7V8 but never used)
SOLD
Mazda MX5 Seats - superb, black cloth, complete with runners
SOLD
Triumph 4 cylinder aluminium alloy bell housing, Very rare
aluminium bell housing for a small chassis Triumph fitted with a 4 cylinder
engine. Fits 1300 to 1500 engine. Has been modified for use with either 3 rail
(early cars) or single rail (later cars, e.g. 1500 Spitfire) gearbox. Huge
weight saving over the original cast iron unit. This is a genuine Triumph part
and was fitted to small number of Triumph Spitfires in the late 60s. Does not
fit 6 cylinder cars.
SOLD
Ford
Falcon/Mustang dual brake master cylinder, 1" bore - small amount of use
nut very much as new but with a slight dent in
the cap. Part MC71248 and F71248
SOLD Triumph TR5 / TR6 drive shafts and output flanges. With new
wheel bearings, U/Js, gaiters and dust shields etc - superb and professionally
fully rebuilt, these are as new and truly superb
SOLD Triple Weber 40 DCOEs - fully cleaned and rebuilt and with short ram pipes,
superb condition. Ideal for 6 cylinder Triumph engine; Deep K&N air filters for Weber DCOE or Dell'Orto DHLA, 3
available, new and unused; Inlet manifold for Triple Weber DCOE or Dell'Orto DHLA carbs;
suits Triumph GT6 or 60s/70s TVR with Triumph 6 cylinder engine, as new,
complete with linkage bar and brake vacuum take-off.
SOLD Spax Krypton adjustable rear shock absorbers for Mustang or
Falcon - pretty sure they fit all 60s Mustangs, can send measurements if needed
- Not new but in superb condition and complete with nuts and rubber bushes.
I send world-wide, but if you want something large, you'll have to come and get it - I live in Gravenhurst (between Bedford and Luton, Beds). Minimum delivery charge is £5 except where marked. UK payment in £UK by PayPal, cash or cheque - please contact me prior to doing that though. USD payment possible by prior arrangement.
E-Mail
Jon Wolfe
or call on 01462 713690